News

With the continuous developmen¥★t of China's eco‌"<±nomy, the development of China ♥9;s CNC machine tool industry in th±'βλe past few years can be said to be¥✘>↓ a rapid progress, especially the emer₽≤φging machine tools - C↑®NC gantry boring and milli≤α©®ng machine, mainly with a base be≠λ↕d, table, left and right colum∞↕> ns, cross beams, roof beams,÷↔↕ connecting beams, boring and₹☆↓↓ milling head and other compon∞™∑ents of the composition of the functi♥★₹on is more complete, China's' ✔® gantry boring and milling♠® machine industry in the China'←↔↓;s self-sufficiency rat↔$↓e in the gantry boring and÷& milling machine indus ∑♣©try is gradually incre™Ωσδasing, the proportion of inσ£≥dependent copyright CNC s≥☆"♦ystem continues to increase. At prese₩₽εnt, not only single head boring a"÷nd milling machine, more'& and more manufacturers began to pay §φ♦♦attention to double spindlΩ✘π♥e boring and milling machine, and co™>•☆ntinue to upgrade and✔£ iteration. The machi↔¥"ne tool environment has always been a¥≥‌₩n important part of the customer'䙧;s attention, which is relatedβ <← to the service life of the mac☆α™hine tool.

CNC Boring and Milling Mac♦♦hine is a kind of highα∑¶-precision machining equipment, w÷♥≈¥e in the installation as well <×₹as the use of the process, especially ₹§to pay attention to avoid d€÷♥amage to the machine too¥δλl. Gantry boring and‌₽ milling machine for the installa>∞tion of the environment is concerned, i♦ ​≥n general, the installat✘✘ion location should be av©‍☆φoided direct sunlight, to avoid • ←the use of humid environment, if the l∏βong-term use of high vi® ¶bration sources or humid e€£>nvironment, will affect the f®£ailure of the internal components o✘€f the machine tool. In additio♦↕n, when connecting the power supply÷λ, the voltage should beπ♣<↑ stabilised, and the fluctua'"™tion of voltage must be within the sp∞π₽γecified range, a little ↕≈§out of this range will causα→e damage to the machine tool motorβ≈α. In addition to the high requireme£¶→≥nts for the installation envΩδironment, we should also pay atγ©tention to the follo♥‍∏wing points in the process of use:

1, in the CNC gantry boring anε‍>×d milling machine around the need to₽☆ leave a certain range of workspace, d∏£¥¶o not allow stacking any it•✘€ems so as not to cause o♠☆Ωbstacles.

2, before the work of the operator mus&δ §t wear good labour protection ★♣clothing, in the oper¶βation of CNC gantry bo☆φεring and milling machine is not abδΩ​le to take gloves.

3, after checking and →‍€φadjusting the parameters ofσ✘ processing, origin and motion •β↕trajectory can be pr± ocessed parts.

4, carefully check the CN¶•C gantry boring and milling machi©¶¶ne workpiece clamping is Ωγnot installed tightly, ±☆each movement bearing is not all retur™γ♠ned to the zero point of t←¶δ™he machine.

5, the use of tools if broken to $↓be replaced in a timely manner, any too©≥×l workpiece is not allowed to beγ <∞ left in the machine tool.

6, the operator must be in accord<→ ®ance with the provisions '≤€↔of the steps to operate th≠✘♥e CNC gantry boring a"Ω nd milling machine, in the process&★≠‍ of work is not allowed to leave thei∞★λr posts, when the CNC ≈γ≈φgantry boring and milling machi×∏≠&ne abnormalities or failuresΩ§ to immediately stop the machine for®∞≈✔ investigation.

7, after the completion of the operati←€on, remember to turn off all the♥α♥± power supply on the CNC gantry borin↕♦g and milling machine  ☆™in order, carefully fill out​π← the records of the shift handover™©←, and finally clean up the s‌ ₩ite.

In addition, in the purchase of boring♠♣÷ and milling machine to do these poin∏≥♥ts, the sense of use wi↓‌ll be greatly enhanced, and effective£÷✘ly avoid the manufacturers repeat&→&ed visits to the maintenance:

1, gantry boring and milling machine ≥'precision selection

Including geometric accuracy, positioni±←ng accuracy, interpolation accu♥•♠βracy and other aspects. The higher 'γthe rigidity of the boring a±$∞γnd milling machine, the better the pre≈✘¶★cision stability of the machine tool.©∏π♣ The worktable is a hydrostati♦✘γ"c guideway, driven by a hydrostati↑ c worm and a worm pick with a ★¶wear-reducing coating, and the smoothn∞✘÷λess of the table movement is good.

2, the speed of gantry bor λ≥ing and milling machine

Improve the CNC boring and millin>'£☆g machine movement speed and feed s™γ∑ peed of the main purpose is£©β to improve processing ef♦&ficiency, improve surface roughness.

3, boring and millin ®&g machine cost-effective

High-performance machinλ©e tools often have a hig'£←h price, penny wise an​™d pound foolish. Do not be g§♦↓'reedy for cheap, the sub ☆♣sequent maintenance costs are×↕π not low.

4, the degree of automation of the ma★σchine tool

If necessary, optional automatic too÷>ε≈l changer tool magaz←©"ine, effectively saving time for tool¶✔₹ change. The spindle can achievπ€e automatic indexing or continuous feeσ→↓ding in three-dimension∑☆‍al space.