News

With the continuous development λ♥☆of China's economy, the <•✔ development of China's CNC machin®​×αe tool industry in the past★≠π few years can be said to b ☆™♥e a rapid progress, especially &✔"the emerging machine ♠✔>tools - CNC gantry boring and milli¥∏→ng machine, mainly with a base bed, ta₩≠ ble, left and right columns,ελ cross beams, roof beams, connectiβσ®'ng beams, boring and milling head ​☆and other components of the compo¶♦✘sition of the function is more c€∏↔omplete, China's gantry bor∑✘ ÷ing and milling machi×☆∞ ne industry in the China's ¶®self-sufficiency rate in tφλ$λhe gantry boring and millin☆♣δg machine industry is gradually φ↔'increasing, the proportion of inde ♠pendent copyright CNC syste↑↑♦✔m continues to increase. At pre£₽'sent, not only single head boring and ε‌λ≠milling machine, more and more manu뱧facturers began to pay attention to douβ×ble spindle boring and mil ÷≈ling machine, and continue to γ upgrade and iteration. The ma πchine tool environment has a&"lways been an important part oπλγ≥f the customer's attention, which♣ε₽ is related to the service lifΩ₩e of the machine tool.

CNC Boring and Milling Machine♠®✘ is a kind of high-precision machining☆↑> equipment, we in the installation ‌♦★∑as well as the use of the pr×£ocess, especially to pay attention to ←'£✔avoid damage to the machine too←α≈↑l. Gantry boring and milling machi​✘ne for the installation o•→‍✔f the environment is cγ ‌♣oncerned, in general, the installatio©¶₽>n location should be avoided direct sun♠Ωγ&light, to avoid the use of €♠≥§humid environment, if the long-term useγ& of high vibration source★φ's or humid environme☆¥§nt, will affect the failure of Ωγ←the internal components of↔‍ the machine tool. In addit±¶•​ion, when connecting the pow ¶∏er supply, the voltage s φhould be stabilised, and the fl​∏♥uctuation of voltage must be within the&≤ specified range, a little out δ&∏of this range will cause d☆‌amage to the machine tool motor. I>φ₹n addition to the high requirement↓≠€s for the installation environment,★‍₹< we should also pay att'↓ention to the following points in "♣the process of use:

1, in the CNC gantry boring and≤₩♣✔ milling machine around the need to lea♣∑✘ve a certain range of workspace, do•≥&$ not allow stacking any items δ so as not to cause obstacles.

2, before the work of ♦±‍the operator must wear∏₩ good labour protection c☆σlothing, in the operation of CNC gantry​≥ boring and milling machine ©♣β≈is not able to take glovΩ∞↑es.

3, after checking and adjusting the α•parameters of processing, origin and ™₽≥motion trajectory can be proces₹£¶←sed parts.

4, carefully check the CNC gantry bo∞♣>ring and milling machine workpiece cla×↓βmping is not installed tightδ&₽∑ly, each movement bearing is not∞  all returned to the zero po♠₹☆Ωint of the machine.

5, the use of tools if broken to be rβ←∞✘eplaced in a timely manner, an≈♦↕y tool workpiece is not all≈ ≥§owed to be left in the ↓≤machine tool.

6, the operator must be i•→₩‌n accordance with the¶<  provisions of the steps to operate th≠☆™✔e CNC gantry boring and milling machine₹☆, in the process of work is notφ↓β§ allowed to leave their  ↕ ≠posts, when the CNC gantry boring♥±♠≠ and milling machine abno"σ↔rmalities or failures tλε←<o immediately stop the mac×™hine for investigation.

7, after the completion of the ope€♣↔§ration, remember to turn off all the♣€♦ power supply on the CNC gantπ♣ry boring and milling machine in o≤♠φ✔rder, carefully fill out the recor↔↕ds of the shift handover, and finally →ε★clean up the site.

In addition, in the purcha♥ ©se of boring and milling machine to do ®α₽✔these points, the sense of≈δ use will be greatly enhanced, and effe$£γctively avoid the manufacture₹♣rs repeated visits to the mai‍γδ ntenance:

1, gantry boring and ™∏φ milling machine precision selecti♣↕φon

Including geometric accuracy♥≠ •, positioning accuracy, inte÷≥↕ rpolation accuracy a&βnd other aspects. The higher'£≠∑ the rigidity of the boring and mill♠₹¶ing machine, the betteα₽>↔r the precision stabili©≤•©ty of the machine tool. The wor ₩ktable is a hydrostatic guidew♦'ay, driven by a hydrostatic wo<  →rm and a worm pick with a wea✘<∞r-reducing coating, and the sm&$'δoothness of the table ∏✔™movement is good.

2, the speed of gantry b→≈oring and milling ma¶€chine

Improve the CNC boring and milling mach↑‌ine movement speed and feed speed of •₽ the main purpose is to improve"♥ processing efficiency, improve ∑<surface roughness.

3, boring and milling machine co∑₩ st-effective

High-performance machine tools often h♠↑™±ave a high price, penny wisα€∏≈e and pound foolish. Do not   be greedy for cheap, the subsequent m₹€aintenance costs are  ←€♠not low.

4, the degree of auto♠↑∑mation of the machine₹> tool

If necessary, optional automatε§ic tool changer tool magaz↑"εine, effectively saving♥₩ time for tool change. The s&✔$pindle can achieve au¥‌ tomatic indexing or continuo δαus feeding in three-™→¶dimensional space.